Page 1 of 1

1 - Relay kit contents

Posted: Fri Dec 01, 2017 6:32 am
by Tony
This covers the original Kickstarter 'Relay' 5-tube clock module which as supplied can be used with IN-14 and IN-8-2 nixies. Other similar sized tubes will laso work with varying modifications.
You should have received the following:
  • 1x Bag1 - a pink electrostatic safe bag with all of the electronic components.
    1x Bag2 - The paxolin case pieces
    1x Levitating magnet
    1x IN-19 nixie
You may also have received 4x IN-14 or IN-8-2 nixies if the version you bought included them.

Image

Re: Relay kit contents

Posted: Fri Dec 01, 2017 7:48 am
by Tony
The case 'Bag2' contains:
  • 1x PCB
    1x Base panel, 0.8mm laminate
    1x Notched loop, 0.8mm laminate
    2x 'narrow shaped' loops, 1.5mm laminate
    1x 'wide shaped' loop, 1.5mm laminate
    2x 'narrow plain' loops, 1.5mm laminate
    3x 'wide plain' loops, 1.5mm laminate
    1x Top panel, 1.5mm laminate
Image

Re: Relay kit contents

Posted: Fri Dec 01, 2017 7:49 am
by Tony
The Relay component Bag1 packing list is:
  • R1,2,4,5,7,8,11,12,14,15
    750k 0603 x10

    R3,6,9,13,17
    10k 0603 x5

    R16
    91R 0603 x1

    rx,y
    470r 0603 x2

    C1,2,3,4,5
    2u2 16/25V X7R 1206 x5

    C6,7,8,9,10,11,12,13,14
    100n 50V X7R 0603/0805 x9

    C15,21
    1n 50V 5% C0G 0805 x2

    C16 x3
    4n7 50V 5% C0G 1206 x3

    C17,18
    100n 200V X7R 1206 x2

    D1
    3V9 Zener 500mW MELF x1

    D2,6,7,10,11,12,13,14,15,16,17,18,19
    LL148 LL44148 MELF x13

    D3,4,5
    BAV99 SOT23 x3

    D8,9
    75V 500mW Zener MELF x2

    LED1,2,3,4,5,6,7
    WS2812B RGB LED 4 pin x7

    T1,2,3,4,5,6,7,8,9,10
    BSS123 SOT23 x10

    T11,13,15,17,19
    MMBTA92 SOT23 x5

    T12,14,16,18,20
    MMBTA42 SOT23 x5

    IC1
    PIC x1

    IC2
    CD4028B SOIC16 x1

    IR receiver
    CHOD x1

    Wire
    0.20mm copper 50 turns x1

    Solder
    0.47mm 10 turns x1

    Pins
    40x1 strip x1.5 (60 pins)

    Nixie sockets x5

    Sticky pads x3

    M3x20 CS bolt x2

    M3 brass nut x2

    M3 Brass washer x2
Note some of the component sizes may differ slightly, if so it'll be mentioned during the assembly.

Image