Piece display PCB

Assembly instructions for the V1 chessboard.
Tony
Site Admin
Posts: 957
Joined: Tue Jul 24, 2012 8:05 pm

Piece display PCB

Post by Tony »

For this you will need the entire contents of BAG 4 plus the M5 nuts and bolts from BAG 1, solder from BAG 5 and copper wire.

Remove the surface mounted components from their tapes. Only one of each type of part is used so there is no risk of mixing up different values or types.

You will have:
Dual diode packs - these are small rectangular 3-legged black plastic blocks. 3 are needed for each board.
Single diodes - Copper-orange glass cylinders with a black band marking one end. These are polarised and must face the same way as on the example baord. One is needed for each board.
Capacitors - Beige rectangular ceramic blocks. Seven of these are used on each board.

Separate the foil cpacitors into another pile, these are cream plastic blocks with 2 wires and '10n' marked on them and the 'D' connectors into another pile. Put these piles of components to one side until the coil winding is done.

Image
Tony
Site Admin
Posts: 957
Joined: Tue Jul 24, 2012 8:05 pm

Re: Piece display PCB

Post by Tony »

Assembling the coil former:

You will need one PCB, one 1.5mm thick spacer and one 0.8mm thick base:

Image

Use a polish block or fine emery paper to clean the surface of the copper PCB and check for any copper whiskers that may cause shorts.

Assemble these pieces on a 5mm bolt in this order and hand tighten the nut:


Image

At this stage it's worth running a few drops of superglue into the groove to hold the pieces together.

Make sure the notches formed by the 2 holes drilled into the edge of the PCB are clear, then feed the copper wire from the top of the PCB through one notch into the groove formed between the PCB and the baseplate.

Wind 46 turns of wire into the groove then feed the wire back through the second notch to the PCB top.


Image

Fix the coil turns in place with varnish or superglue and wait for it to set/harden.


Trim the wire ends as shown, scrape off the insulation and solder them to the PCB.

Image

Repeat 32 times. :o :cry:
Tony
Site Admin
Posts: 957
Joined: Tue Jul 24, 2012 8:05 pm

Re: Piece display PCB

Post by Tony »

PCB assembly:

Place a spot of solder here for the glass diode:

Image

Pick up the diode and solder in place. Once the solder has hardened solder the other end. Make sure it's this way round:

Image

Place solder spots as shown for the capacitors:

Image

Solder the capacitors onto these spots and solder the other ends. These can go either way round:

Image

Place solder spots as shown for the diode packs:

Image

Solder these in place. They can only fit one way round as long as you make sure the side with markings is facing up.

Image

Trim the leads of one 10n capacitor to about 5mm long and bend outwards slightly. Place it in the cutout as shown:

Image

Solder it in place. That's the PCB completed except for the pins, the position of these will depend on the letter you want to display.

Image

Repeat again 32 times :lol:

You should now have 33 base PCB/coil assemblies ready for pins.
Tony
Site Admin
Posts: 957
Joined: Tue Jul 24, 2012 8:05 pm

Re: Piece display PCB

Post by Tony »

Display socket pins:

Take one of the 15-pin 'D' sockets and cut open one rivet:

Image

Open up the socket housing and remove the pins.

Image

Cut the excess pin off just below the centre bulge.

Image

Solder 2 or 3 of the pins to the PCB as required - I used 2 and it held the display but yo may want to use 3 for extra stability:

Image
Tony
Site Admin
Posts: 957
Joined: Tue Jul 24, 2012 8:05 pm

Re: Piece display PCB

Post by Tony »

Pin positions for various pieces:

minion: 16x

Image

King (IN-7) and Knight (IN-7A): 6x

Image

Alfiere: 4x

Image

Vizier: 2x

Image

Tower (IN-7A): 4x

Image

Now form a solder bridge between the cathode pin and the ground loop:

Image
Locked